1.將機器放置在平坦的地面上或工作臺上，將插頭插入220v電源插座中。
1. Place the machine on a flat ground or workbench, and insert the plug into a 220V power socket.
2.接通電源后打開電源開關，"on"指示燈亮起為正常通電狀態，"off"指示燈滅為斷電狀態。
2. Turn on the power switch after the power is turned on, and the "on" indicator lights up as the normal power on state, and the "off" indicator lights off as the power off state.
3.按下啟動按鈕3秒鐘后機器開始運轉并進入正常工作程序。
3. Press the start button for 3 seconds, and the machine starts to run and enter the normal working procedure.
4.機器運行過程中如發現異?，F(xiàn)象應立即切斷總電源開關或關閉電磁鐵控制電路板上的手動復位按鈕進行緊急處理。
4. If any abnormal phenomenon is found during the operation of the machine, the main power switch shall be cut off immediately or the manual reset button on the solenoid control circuit board shall be turned off for emergency treatment.
5.在使用過程中嚴禁用手直接接觸電機旋轉部分以免發生意外事故造成人身傷害！
5. It is strictly prohibited to directly touch the rotating part of the motor with hands during use to avoid personal injury caused by accidents!
6.使用完畢請立即切斷總電源并將插頭拔出以防觸電危險！
6. After use, please cut off the main power supply immediately and pull out the plug to prevent electric shock!
7.如遇停電或其它原因需要暫時停止工作時必須先將電磁鐵關掉方可停機！
7. In case of power failure or other reasons that require temporary stop of work, the electromagnet must be turned off before shutdown!
8.本產品不適用于有易燃易爆氣體場所或有腐蝕性氣體的場所使用！
8. This product is not suitable for use in places with flammable and explosive gas or corrosive gas!
1、設備啟動前應檢查設備是否具備啟動條件。
1. Before starting the equipment, it is necessary to comprehensively check whether the equipment has the conditions for safe starting.
2、明確操作任務和注意事項。
2. Specify operation tasks and safety precautions.
3、開啟電源，設備電源指示燈亮方可進行操作。
3. Turn on the power supply, and the device power indicator is on.
4、按下設備控制箱上的“球根啟動”或“葉菜啟動”按鈕，設備開始運轉
4. Press the "bulb start" or "leaf vegetable start" button on the equipment control box, and the equipment starts to run
5、葉菜類加工時，可調節“回旋刀速度”和“輸送機速度”來控制葉菜類的規格。
5. During the processing of leaf vegetables, the "revolving knife speed" and "conveyor speed" can be adjusted to control the specifications of leaf vegetables.
6、機器運轉過程中，切勿將手或硬物伸進防護網中，以免造成人身傷害和損壞機器。
6. During the operation of the machine, do not put your hands or hard objects into the protective net to avoid personal injury and damage to the machine.

7、機器運轉過程中，如發現機器運轉聲音不正常，必須立即停止檢查，待排除異常后方能后方能繼續工作。
7. During the operation of the machine, if it is found that the running sound of the machine is abnormal, the inspection must be stopped immediately, and the work can be continued only after the abnormality is eliminated.
8、運行中，不間斷的檢查成品的規格，及時調整速度，做到規格統一，如有異常及時停止。
8. During operation, the specification of finished products shall be checked continuously, the speed shall be adjusted in time, and the specification shall be unified. In case of any abnormality, it shall be stopped in time.
9、蔬菜加工完畢后，按下控制箱上的“球根停止”或“葉菜停止”，設備停止運轉并關閉設備控制電源。
9. After vegetable processing, press the "bulb stop" or "leaf vegetable stop" on the control box to stop the equipment and turn off the equipment control power.
10、加工完畢后，清理現場，做準備清理設備的前期準備。（包括：清理現場、準備工具、拆卸刀頭等）
10. After the processing is completed, the site shall be cleaned and the preliminary preparation for equipment cleaning shall be made. (Including: cleaning the site, preparing tools, disassembling cutter head, etc.)
11、沖洗設備前應檢查電源線是否有損壞，沖洗設備時，注意控制不能把水濺到電機上，以免造成機器的損壞。
11. Before washing the equipment, check whether the power cord is damaged. When washing the equipment, pay attention not to splash water on the motor to avoid damage to the machine.
12、在拆卸或清洗道具的過程中，不要用手直接觸摸刀刃。拆卸時要用手拿刀組上端的軸部，必要時戴上保護手套，以免發生危險。
12. Do not touch the blade directly with your hands during disassembly or cleaning of props. When disassembling, take the shaft at the upper end of the cutter set by hand, and wear protective gloves if necessary to avoid danger.
以上就是為大家介紹的有關切絲切片機的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://vrhbo.cn/
The above is a detailed introduction to the shredding and slicing machine. I hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional services http://vrhbo.cn/